What is a kickboard on a stair?

Kick board are panels beside the stairs on the inside or outside. They can also cover the expansion joint between floors. Side trim covers expansion joints or the side of the bottom plate. Treads, Inside Kickboard, no Outside.

Do I need a skirt board on stairs?

You do not need a skirt board on stairs. If you don’t have baseboards in your house, then you don’t need skirting for your stairs. You might want stair skirting if you have baseboards in your house, as skirting will serve to connect, esthetically, baseboards on either ends of the step.

Which goes first tread or riser?

When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser. Treads and risers fasten with construction adhesive to the subfloor.

What do you put on stair risers?

You can install tiles on the risers of your interior stairs quite easily. If the size of the tile matches the height of the riser, you just need to attach the tiles to the risers—no cutting required. If you do need to cut tiles, you can cut tiles cleanly with a wet tile saw.

How thick is a stair skirt board?

The stair skirt board is a long, unbroken piece of trim, 9 ½ inches wide and ⅝ inches thick. It’s fitted along the closed end of the stairs and is made from a range of materials. Hardwood is usually used to match the stair treads. MDF and softwood are used if the skirting board is to be painted.

What size board is used for stairs?

It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.

What is the wood on the side of stairs called?

A stringer is the support board that runs along each side of the staircase. The treads and risers are fixed into the stringer or stringer board. A staircase always has two stringers. The inner stringer is located against the wall, while the outer stringer is on the side of the staircase open to view.

Do you put baseboard on stairs?

Install baseboard directly on top of stair stringers. Remember the stud pattern may change between floors, and there is no bottomplate to nail into.

Should you nail or screw stair treads?

Don’t fasten treads and or risers with only nails or staples. The adhesive is much more important than the fasteners. There will be times when fastening may be limited, so a good adhesive is critical. Don’t use the stringer as a level for the treads.

Can I just glue stair treads?

A polyurethane glue, such as Loctite PL Premium, is a highly recommended adhesive. Since the stair treads, or the surface of your stairs, receives a lot of foot traffic, you’ll want to make sure it’s properly installed.

What can you put on stairs besides carpet?

It is possible to install any flooring material, with each having its own unique advantages and disadvantages.

• Stair Runner Carpet. The flooring is great for stairs.
• Luxury Vinyl Tiles (LVT)
• Laminate Flooring on Stairs.
• Luxury Vinyl Flooring on Stairs.
• Hardwood Stairs.
• Stair Tiles.

What boards are used for stairs?

What Wood Is Best for Stair Treads?

• Oak Stair Treads. Oak is a common type of wood for stair treads.
• Hickory Stair Treads. Hickory is another common choice for wood stair treads.
• Maple Stair Treads. Maple’s tan and white hues make it a popular choice for a range of wood products.
• Poplar Stair Treads.
• Walnut Stair Treads.

What is the molding on the side of stairs called?

Skirtboard. A trimboard running with the rake, pitch or incline of the stair against the wall on the closed side of the staircase. While usually nonstructural, skirtboard protects the drywall surface and adds to the décor of the staircase.

What is the bottom of stairs called?

The post (also called a newel) is the vertical structure that connects the stair or floor to the railing system. Spindles, which are vertical wood or metal structures, are interspersed between posts to provide a safety barrier along the stair system. Shoe is the bottom plate that spindles (or glass) are set into.

Do you paint treads or risers first?

Once the stairs are ready, it’s best to start by painting the risers. That way, you can remove any paint you get on the treads before staining them; and painted risers are relatively easy to protect from stain. Choose semigloss or gloss paint — both are easier to keep clean than flat paint.

What goes on first stair tread or riser?

Do you put risers or treads first?